Skip to main content

NTP SERVER RedHat


Server Configuration

  • Install the ntp package:
[root@host ~]# yum install ntp
  • Ensure the following entries are in /etc/ntp.conf:
    • The below example functions as a NTP server to the 192.168. network.
[root@ntp.server.com ~]# cat /etc/ntp.conf
restrict default kod nomodify notrap nopeer noquery
restrict -6 default kod nomodify notrap nopeer noquery
restrict 127.0.0.1
restrict -6 ::1
server stratum2.ntp.com
server stratum2.ntp2.com
restrict 192.168.0.0 mask 255.255.0.0 nomodify notrap
driftfile /var/lib/ntp/drift
keys /etc/ntp/keys
Note: The public stratum 2 servers for your network's NTP server can be found on ntp.org.
  • Start the ntpd service:
[root@ntp.server.com ~]# service ntpd start

Client Configuration

  • Ensure the following entries are in /etc/ntp.conf:
[root@ntp.client.com ~]# cat /etc/ntp.conf
restrict default kod nomodify notrap nopeer noquery
restrict -6 default kod nomodify notrap nopeer noquery
restrict 127.0.0.1
restrict -6 ::1
server ntp.server.com
driftfile /var/lib/ntp/drift
keys /etc/ntp/keys
  • Start the NTP service:
[root@ntp.client.com ~]# service ntpd start

Comments

Post a Comment

Popular posts from this blog

memory error detect XSCF uboot

If you see something like this when you poweron you server: memory error detect 80000008, address 000002d0 data 55555555 -> fbefaaaa capture_data hi fbefaaaa lo deadbeef ecc 1b1b capture_attributes 01113001 address 000002d0 memory error detect 80000008, address 000002d4 data aaaaaaaa -> deadbeef capture_data hi fbefaaaa lo deadbeef ecc 1b1b capture_attributes 01113001 address 000002d4 memXSCF uboot  01070000  (Feb  8 2008 - 11:12:19) XSCF uboot  01070000  (Feb  8 2008 - 11:12:19) SCF board boot factor = 7180     DDR Real size: 256 MB     DDR: 224 MB Than your XSCF card is broked. Replace it with new one. After that it will ask you for enter chassis number - located at front of the server XSCF promt to enter your chasses number ( is a S/N of your server ): Please input the chassis serial number : XXXXXXX 1:PANEL Please select the number : 1 Restoring data from PANEL to XSCF#0. Please wait for se...
1 comment
Read more

Solaris. remove unusable scsi lun

Solaris remove unusable or failing scsi lun 1. The removed devices show up as drive not available in the output of the format command: # format Searching for disks...done ................      255. c1t50000974082CCD5Cd249 <drive not available>           /pci@3,700000/SUNW,qlc@0/fp@0,0/ssd@w50000974082ccd5c,f9 ................      529. c3t50000974082CCD58d249 <drive not available>           /pci@7,700000/SUNW,qlc@0/fp@0,0/ssd@w50000974082ccd58,f9 2. After the LUNs are unmapped Solaris displays the devices as either unusable or failing. # cfgadm -al -o show_SCSI_LUN | grep -i unusable # # cfgadm -al -o show_SCSI_LUN | grep -i failing c1::50000974082ccd5c,249       disk         connected    configured   failing c3::50000974082ccd58,249 ...
1 comment
Read more

FOS Password recovery (Brocade Fabric OS Switch Password recovery procedure)

Password recovery using root account If you have access to the root account, you can reset the passwords on the switch to default. This feature is available for all currently supported versions of the Fabric OS. Follow the below steps to reset any account password from the root account. 1. Open a CLI session (serial or telnet for an unsecured system and sectelnet for a secure system) to the switch. 2. Log in as root. 3. At the prompt, enter the passwddefault command as shown below: switch:root> passwddefault 4. Follow the prompts to reset the password for the selected account. For example: switch:root> passwddefault All account passwords have been successfully set to factory default. Once the passwords have been reset, log into the switch as admin, and modify your default passwords. Make sure to keep a hardcopy of your switch passwords in a secure location. The default passwords for Fabric OS switches are: Root fibranne Adminpassword Userpassword Password r...
4 comments
Read more